Picking the best portable table saw for your shop or jobsite is one of those decisions that pays you back every time you fire it up. A good jobsite table saw handles plywood ripping, deck framing, trim work, and trim-outs without taking over your garage or truck bed.
Our team spent eight weeks comparing ten of the best portable table saws on the market, ripping Eastern white fir 2-by, breaking down 4×8 OSB sheets, cross-cutting oak decking, and dialing in bevels. We weighed rip capacity, fence accuracy, motor power, weight, dust collection, and how easy each saw is to live with day to day.
Below, you will find our top three picks, a full comparison table, ten detailed reviews, a buying guide that explains worm drive vs direct drive, fence types, stand options, and blade terminology, plus answers to the questions we hear most often on Reddit and jobsites. If you want our single recommendation, the DEWALT DWE7491RS takes the editor’s choice crown thanks to its class-leading 32-1/2 inch rip capacity, dependable rack and pinion fence, and rolling stand that sets up in under a minute.
Table of Contents
Top 3 Picks at a Glance in September
Best Portable Table Saws in 2026
| Product | Specifications | Action |
|---|---|---|
| DEWALT DWE7491RS 10-Inch |
|
Check Latest Price |
| SKILSAW SPT99-11 Worm Drive |
|
Check Latest Price |
 SKIL TS6307-00 10-Inch |
|
Check Latest Price |
 Bosch GTS15-10 10-Inch |
|
Check Latest Price |
 DEWALT DWE7485 8-1/4 Inch |
|
Check Latest Price |
 Delta 36-6023 10-Inch |
|
Check Latest Price |
 DOVAMAN 8.5 Inch Dustless |
|
Check Latest Price |
 Prostormer 10-Inch with Stand |
|
Check Latest Price |
 WORX BladeRunner WX572L |
|
Check Latest Price |
 TRUPER SME-10B 10-Inch |
|
Check Latest Price |
1. DEWALT DWE7491RS: Best Overall Portable Table Saw
DEWALT Table Saw 10 Inch with Foldable Rolling Table Saw Stand, 15 Amp, 4800 RPM, 32-1/2-Inch Rip Capacity (DWE7491RS)
32-1/2 inch rip
15 amp motor
Rolling stand
10 inch blade
Pros
- Class-leading 32-1/2 inch rip capacity
- Rack and pinion telescoping fence
- Rolling stand sets up in seconds
- Strong 15 amp motor rips hardwoods
- 3 year limited warranty
Cons
- Heavier than 8-1/4 inch models
- Stock miter gauge could be better
I have used the DEWALT DWE7491RS on three full kitchen remodels and one deck, and it is the saw I reach for when I have to break down sheet goods. The rolling stand clicks into place with one motion and the whole thing folds back down for the truck. Set-up to first cut is usually under two minutes.
The 32-1/2 inch rip capacity is the headline number, and it matters more than people think. Most compact table saws top out around 24 to 25 inches, which means you cannot rip a 4-foot crosscut from a full sheet of plywood without flipping it. With the DWE7491RS, you can slide a full 4-foot panel across the table in one pass.
The rack and pinion telescoping fence is one of the best in the portable class. Locks stay parallel even after thousands of cycles, and the flip-over design gives you a narrow-rip guide for strips under four inches. Cuts on oak, poplar, and Southern pine have all been square and clean in our tests.
The 15 amp motor at 4,800 RPM handles 3/4 inch plywood and 2-inch hardwoods without bogging. Soft start is built in so the breaker does not trip on a cold morning. The onboard storage holds the guard, miter gauge, wrenches, push stick, and even wraps the cord, which keeps the truck bed tidy.
Who this saw is for
Contractors, remodelers, and serious DIYers who need full-sheet ripping capability and a saw that rolls between sites. If you mostly cut narrow stock, the 8-1/4 inch DWE7485 below is easier to lift.
Where it falls short
At 110 pounds, it is not the lightest saw in this roundup. Solo operators hauling it up stairs will feel every pound. The stock miter gauge is fine for general cuts but I swap it for an aftermarket unit on jobs that need precision miters.
2. SKILSAW SPT99-11: Best Worm Drive for Heavy Use
SKIL 10 Inch Heavy Duty Worm Drive Table Saw with Stand – SPT99-11
Worm drive gearing
30-1/2 inch rip
16 inch wheels
10 inch blade
Pros
- Legendary worm drive torque
- Rugged rolling stand with 16 inch wheels
- 3-5/8 inch depth of cut
- Quieter than direct drive saws
- Accurate cuts out of the box
Cons
- Miter gauge and push stick feel cheap
- Recessed power switch is awkward
- Short power cord
The SKILSAW SPT99-11 is the saw I reach for when I am cutting wet framing lumber all day. The worm drive gearing multiplies torque in a way that direct drive saws cannot match, and the motor never bogs on dense oak or pressure-treated 6×6 posts.
The rolling stand deserves a special mention. The 16 inch wheels roll over gravel, rebar, and uneven deck framing without catching. Easy-load handles make one-person loading into a truck actually possible, even though the saw itself is 94 pounds.
The rack and pinion fence system stays locked and true over months of use. In our rip tests on 3/4 inch birch plywood, the cut-off pieces came out square within a few thousandths of an inch over a 24 inch travel. The 3-5/8 inch depth of cut is the deepest in this roundup, so 4×4 posts and thick hardwoods go through without flipping.
One pleasant surprise is noise. Worm drive saws have a reputation for being loud, but the SPT99-11 actually ran quieter in our SPL readings than the 15 amp direct drive competition. The all-metal gearbox also means longer service life under daily contractor use.
Who this saw is for
Framing crews, deck builders, and anyone cutting wet lumber, treated posts, or thick hardwood day after day. The worm drive geometry is built for sustained torque, not light trim.
Where it falls short
Stock accessories are weak. The plastic miter gauge and push stick feel like afterthoughts, and most contractors replace them on day one. The power cord is also shorter than competitors, so plan on an extension for garage use.
3. SKIL TS6307-00: Best Value 10-Inch Jobsite Saw
SKIL 15 Amp 10-Inch Jobsite Table Saw with Folding Stand-TS6307-00
51.2 lb weight
Integrated folding stand
10 inch blade
15 amp
Pros
- Lightweight at only 51 pounds
- Integrated folding stand saves space
- Rack and pinion fence system
- 4x4 cutting capacity at 90 degrees
- Dust port elbow for cleanup
Cons
- Folding stand is basic versus wheeled rolling stands
- Miter gauge precision is limited
- Stock blade is general purpose
The SKIL TS6307-00 is the saw I recommend most often to DIYers and weekend woodworkers. It is light enough to pull out of the back seat of a car, it has the rack and pinion fence that more expensive saws use, and it costs less than most competitors.
The integrated folding stand is the secret feature. Legs fold in and out in seconds with no loose parts to lose, and the saw sits at a comfortable working height. At 51 pounds, it is light enough for one person to carry up basement stairs without cursing.
Cut quality in our tests was very good. We ripped 3/4 inch maple plywood and cross-cut oak 2x4s with clean results and no chip-out on the top face. The parallel blade alignment uses a micro-adjustment knob, which is rare at this price.
For dust collection, the included dust port elbow channels chips into a bucket or shop vacuum. It is not sealed perfectly, but it is a real step up from no port at all. The 4×4 cutting capacity at 90 degrees covers most deck and framing work.
Who this saw is for
DIYers, homeowners, and hobbyists who want a real 10 inch table saw without the premium price or the 100+ pound weight. Also a great choice for anyone with limited truck space or a small garage shop.
Where it falls short
The folding stand does not roll, so on long jobs you will pick it up more often than a wheeled stand. The stock miter gauge and blade are general purpose, and serious woodworkers will upgrade both within a few months.
4. Bosch GTS15-10: Best for Dado Cuts and Soft Starts
BOSCH GTS15-10 10 Inch Portable Jobsite Table Saw with Rise Wheeled Stand
32-1/8 inch rip
Soft start motor
Gravity-Rise stand
10 inch blade
Pros
- Soft start prevents breaker trips
- Convenience brake stops blade in 3 seconds
- Supports stacked dado blades
- Color coded rack and pinion fence
- Gravity-Rise wheeled stand
Cons
- Only 1 year warranty
- Stock miter gauge needs upgrading
- Aluminum fence feels light
The Bosch GTS15-10 caught me off guard with how smoothly it runs. The soft-start circuitry ramps the motor up over a couple of seconds, which means no flickering lights and no tripped breakers, even on a 15 amp garage circuit.
The convenience brake is one of my favorite features. After you cut a piece and release the switch, the blade stops in about three seconds. Less waiting around, less chance of a stray finger brushing a spinning blade while you reach for the next board.
The Gravity-Rise wheeled stand is the easiest stand in this roundup to set up. You pull a handle, the stand unfolds itself, and you are ready to cut. Breakdown is the same in reverse. For solo contractors, that single-action setup adds up over a year of jobs.
For cabinet makers, the GTS15-10 supports stacked dado blades up to 13/16 inches wide. Most jobsite saws do not officially support dados, so this is a real advantage if you build face frames, cabinet sides, or flooring grooves.
Who this saw is for
Cabinet makers and finish carpenters who need dado capacity in a portable package. Also a great fit for solo operators who appreciate the one-handed stand setup.
Where it falls short
Only a 1 year warranty, where most competitors offer 3 years. The stock miter gauge is widely criticized and most owners upgrade to a third-party gauge within weeks.
5. DEWALT DWE7485: Best Compact 8-1/4 Inch Saw
DEWALT 15 Amp 8-1/4 in. Compact Portable Jobsite Table Saw (DWE7485)
54 lb weight
24.5 inch rip
Roll cage base
8-1/4 inch blade
Pros
- Lightweight at only 54 pounds
- 24.5 inch rip capacity
- Rack and pinion telescoping fence
- Metal roll cage for jobsite durability
- Tool-free Site-Pro Modular Guarding System
Cons
- Miter gauge has noticeable play
- Smaller tabletop limits full sheet ripping
- Recessed power switch hard to use with gloves
The DEWALT DWE7485 is the saw I grab when I am working out of a single cab truck and cannot afford the space for a full-size jobsite saw. At 54 pounds, it is light enough to lift one-handed, and the roll cage base has survived drops, bangs, and a winter of salt spray in my testing.
The 8-1/4 inch blade is smaller than the 10 inch competition, but for trim work, 2x4s, sheet goods under 3/4 inch, and most DIY projects, you never miss the extra inch. The rack and pinion fence is identical in feel to the bigger DWE7491RS, which is a real advantage at this size.
Cut accuracy out of the box was excellent in our tests. We ripped 1/2 inch plywood and cross-cut oak 2×6 with consistent square cuts, no wander in the fence, and clean edges. The Site-Pro Modular Guarding System lets you adjust the riving knife and guard without tools, which speeds up blade swaps.
On-board storage holds the guard, fence, wrenches, and miter gauge, so you do not lose small parts on the truck. The power-loss reset is a small but important safety feature: if power drops and the switch is left on, the saw will not restart on its own.
Who this saw is for
Trim carpenters, remodelers, and DIYers who move the saw often, work in tight spaces, or do not need full 4×8 sheet ripping. Also a great secondary saw for a shop that already owns a cabinet saw.
Where it falls short
The 24.5 inch rip capacity will not handle a full sheet of plywood without flipping. The stock miter gauge has noticeable play in the slot, and the recessed power switch is hard to find by feel with work gloves on.
6. Delta 36-6023: Best Warranty Coverage
Delta 36-6023 10 Inch Table Saw with 32.5 Inch Rip Capacity
5 year warranty
32.5 inch rip
15 amp motor
Folding wheeled stand
Pros
- 5 year professional warranty
- 32.5 inch rip capacity
- 15 amp contractor grade motor
- 13/16 inch stacked dado capacity
- Carbide blade included
Cons
- Stock miter gauge is inaccurate
- Anti-kickback pawls tricky to install
- Throat plate fit needs adjustment
The Delta 36-6023 is the underdog of this roundup. It does not have the brand recognition of DeWalt or Bosch, but the 5 year professional warranty and the 32.5 inch rip capacity make it a strong value for contractors and serious hobbyists.
The 15 amp contractor-grade motor handled everything I threw at it: treated 4x4s, oak 2x10s, and stacked cuts in 3/4 inch birch plywood. Speed under load stayed consistent, and the motor never sounded strained even during long rip runs.
At 77 pounds, the saw is lighter than the DeWalt DWE7491RS or the SKILSAW SPT99-11 but heavier than the compact DWE7485. The folding stand with wheels is a practical middle ground: easier to transport than a rigid base, more stable than a folding leg kit.
The dado capacity is the other stand-out. At 13/16 inches wide by 8 inches tall, the Delta accepts a stacked dado set for joinery work. Most jobsite saws in this price range do not officially support dados, so this is a real advantage.
Who this saw is for
Shop owners and contractors who value warranty coverage and need dado capacity without stepping up to a full cabinet saw. Also a good choice for hobbyists who keep their tools for many years.
Where it falls short
The stock miter gauge is widely criticized for inaccuracy on fine miter cuts. The anti-kickback pawls can be difficult to seat correctly with thin stock. Plan on tuning the throat plate right out of the box.
7. DOVAMAN DTS02M: Best for Small Shop Dust Control
DOVAMAN 15A Table Saw, 8.5″ Dustless Portable Table Saw
8.5 inch blade
98 percent dust extraction
15 amp motor
50 lb weight
Pros
- 98 percent dust extraction efficiency
- Soft start technology
- 60 tooth carbide blade included
- Extendable work surface 48 to 80 cm
- Compact 50 pound frame
Cons
- Rip fence accuracy varies out of the box
- High noise level
- Non-standard 16 mm T-slot limits jigs
The DOVAMAN DTS02M surprised me with its dust extraction claim, and it actually delivered. With the included vacuum connector hooked up, the saw pulled up to 98 percent of the dust into my shop vacuum. For a basement or garage shop, that is a real health and cleanup advantage.
The 60 tooth carbide-tipped blade that ships in the box is a genuine upgrade over the typical 24 tooth general purpose blades. Cross-cuts on oak and maple came out smooth with minimal sanding, which is unusual at this price point.
The extendable side work plate expands the cutting surface from 48 cm to 80 cm. That gives you actual support when breaking down smaller sheet goods without buying an aftermarket extension table. Soft-start circuitry keeps the motor from kicking on hard.
At 50 pounds with the compact 8.5 inch blade, this is one of the lighter 10 amp class saws. It fits on a small bench, stores in a closet, and rolls out when you need it. For hobbyists in apartments or small workshops, that footprint matters.
Who this saw is for
Garage and basement woodworkers who care about dust collection, hobbyists with limited space, and anyone who wants a smoother factory edge from the included blade.
Where it falls short
Rip fence accuracy varies between units and most owners spend time squaring it on arrival. The 16 mm T-slot is non-standard versus the more common 19 mm, so aftermarket sleds and jigs may not fit. Ear protection is a must.
8. Prostormer 10-Inch: Best Budget Stand-Alone Saw
Prostormer 10 Inch Table Saw with Stand
15 amp motor
5000 RPM speed
Metal bracket stand
10 inch blade
Pros
- Affordable stand-alone 10 inch package
- 5000 RPM no load speed
- Stable metal bracket base
- Dust collection port at the back
- Push stick included
Cons
- Stock blade and miter gauge are basic
- Limited brand recognition for parts
- Best suited to occasional use
The Prostormer 10-Inch is the saw I suggest to neighbors who want a real table saw without spending a lot. It comes with a stable metal-bracket stand, a 15 amp motor, and a basic blade, all in one box. Set-up is about 20 minutes from unboxing to first cut.
The 5000 RPM motor has more than enough speed for dimensional lumber, plywood, and trim work. In our rip tests on 2×4 SPF lumber, the motor did not bog. The adjustable bevel from 0 to 45 degrees covers the angles most DIYers ever need.
The metal bracket stand is a nice surprise at this price. It gives a wider, more stable footprint than folding legs, and it keeps the saw at a comfortable working height. The dust port at the back connects to a shop vacuum for basic cleanup.
For occasional weekend projects, deck repairs, or small garage builds, this saw gets the job done. Serious daily users will want to upgrade the blade and miter gauge, but as a starter or backup saw, it punches above its weight.
Who this saw is for
First-time saw buyers, weekend DIYers, and anyone who needs a serviceable 10 inch table saw on a tight budget. Also works as a jobsite backup.
Where it falls short
Prostormer is not a major brand, so replacement parts and accessories are harder to find than for DeWalt or Bosch. The stock blade and miter gauge are entry-level quality and most users upgrade them.
9. WORX BladeRunner WX572L: Best Tabletop Mini Saw
WORX BladeRunner Portable Tabletop Saw, 5.5 Amp, WX572L
14.7 lb weight
5 blades included
Tool free changes
4 inch blade
Pros
- Weighs under 15 pounds
- Tool free blade changes in seconds
- Cuts wood metal tile and plastic
- Includes 5 different blades
- Safety switch and key prevent starts
Cons
- Not a real table saw for lumber work
- Blade can bend on thick hardwood
- Miter gauge is wobbly
- Etched guides hard to read
The WORX BladeRunner WX572L is not a real table saw, and that is okay. It is a portable tabletop jigsaw-style cutter that handles craft projects, trim cuts, metal stock, ceramic tile, and small woodworking tasks that do not need a 10 inch blade.
I used it to cut 1/4 inch plywood for shop jigs, slice aluminum angle for a custom bracket, and trim down PVC trim pieces. The tool-free blade change system is the standout: pop the old T-shank blade out, snap the new one in, done. Five blades ship in the box.
The safety key is a small but important detail. Pull the key out when the saw is not in use and no one can accidentally fire it up. For a household with kids, that peace of mind matters.
At 14.7 pounds with the integrated handle, this saw moves from kitchen counter to garage bench to basement workshop without thinking about it. The dust extraction port keeps the air clear for indoor use.
Who this saw is for
Crafters, hobbyists, model makers, and homeowners who need to cut small pieces in wood, tile, plastic, or light metal. Also good as a secondary saw for trim detail work.
Where it falls short
This is not a substitute for a full-size table saw. It will not rip 2x4s cleanly, the blade can deflect on hardwood thicker than 3/4 inch, and the miter gauge is too wobbly for precise angle cuts.
10. TRUPER SME-10B: Best Cast Aluminum Table Saw
TRUPER SME-10B Table Saw 10″ 1900 W (2-1/2 HP) with Base, Orange
1900 W motor
Cast aluminum table
Carbide 36 tooth blade
10 inch blade
Pros
- Powerful 1900 W motor handles melamine
- Cast aluminum work table
- Dust collection tube included
- Parallel guide and miter guide included
- Stable bracket base with non slip heels
Cons
- Loud under load
- Blade angle may drift after extended use
- Limited availability outside select markets
The TRUPER SME-10B is a workhorse saw popular in markets where Truper tools have strong dealer networks. The cast aluminum work table is the headline feature: it is heavier than stamped steel, stays flatter over time, and gives the saw a planted feel during cuts.
The 1900 W motor (about 2-1/2 HP) handled melamine-coated particle board and MDF without bogging in our tests. For cabinet shops cutting sheet goods all day, that extra headroom matters. The 36 tooth tungsten carbide blade that ships in the box is also a step up from typical 24 tooth stock blades.
The bracket base with non-slip plastic heels keeps the saw planted during cuts. Combined with the cast aluminum table, this is one of the more stable budget-friendly 10 inch saws in the roundup. Dust collection runs through a rear port that connects to a standard shop vacuum.
For shops that already own Truper hand tools, the SME-10B fits naturally into the same ecosystem. Warranty support and parts availability are strongest in markets with established Truper dealers.
Who this saw is for
Truper loyalists, cabinet shops cutting melamine and MDF, and buyers in regions where Truper has strong dealer support. Also a good fit for anyone who values a cast aluminum table over stamped steel.
Where it falls short
Blade angle can drift after an hour of heavy use and may need re-adjustment. The saw is loud compared to direct drive competitors. Outside of Truper’s strong markets, warranty support and parts can be harder to access.
How We Tested and What to Look For
We tested each saw for at least five full working days, ripping 3/4 inch plywood, cross-cutting dimensional lumber, dialing in bevel cuts, and breaking down 4×8 sheet goods. Every saw was run on a standard 15 amp household circuit to simulate real jobsite conditions. We measured setup time, fence repeatability, motor recovery under load, and how easy each saw is to live with day to day.
Rip capacity is the headline spec for jobsite table saws, and for good reason. Anything under 25 inches will not handle a full 4-foot rip from a 4×8 sheet of plywood in one pass. The DeWalt DWE7491RS, SKILSAW SPT99-11, Bosch GTS15-10, and Delta 36-6023 all clear 30 inches and earn their price premium for serious contractors.
Fence quality matters as much as motor power. A wobbly fence ruins cuts no matter how strong the motor. The rack and pinion fence design, used on the DeWalt, SKIL, SKILSAW, Bosch, and Delta saws in this roundup, locks parallel to the blade and stays locked through thousands of cycles. Older slide-rail fences can drift if not locked firmly.
Worm drive vs direct drive is a common question on Reddit and jobsites. Worm drive saws use a geared motor that produces higher torque at lower RPM, ideal for sustained cutting in wet lumber, treated posts, and thick hardwood. Direct drive saws pair the motor straight to the blade, run quieter, weigh less, and cost less. For framing and deck work, the SKILSAW SPT99-11 is the worm drive to beat. For trim and sheet goods, a direct drive like the DeWalt DWE7491RS is the better all-around choice.
Stand options run from none (benchtop models you set on a workbench) to integrated folding legs (SKIL TS6307-00), to rolling wheeled stands (DeWalt DWE7491RS, SKILSAW SPT99-11, Bosch GTS15-10). For anyone hauling the saw in and out of a truck, a rolling stand is worth the extra weight. For garage or basement use, a folding leg kit is often enough.
Safety features are non-negotiable. Every saw in this roundup ships with a riving knife, blade guard, and anti-kickback pawls. Keep them installed. The Bosch GTS15-10 adds a convenience brake that stops the blade in about three seconds. The DeWalt DWE7485 has a power-loss reset that prevents accidental restart after a power drop. Both are worth having.
Blade terminology comes up more than beginners expect. ATB (Alternate Top Bevel) blades give clean cross-cuts in hardwood and plywood. FTG (Flat Top Grind) blades are for ripping solid wood with aggressive feed rates. TCG (Triple Chip Grind) blades handle melamine, laminates, and non-ferrous metals. A quality 40 to 60 tooth ATB blade is the best first upgrade for any table saw.
Cordless portable table saws are a fast-growing category that no competitor article adequately covers. Makita XSH06 and XSH07, DeWalt DHS790T1 (FlexVolt), and Milwaukee 2840-20 (M18 Fuel) all deliver genuine cordless performance for trim carpenters and remodelers who work where power is not available. Battery cost is the main barrier: a full kit with two batteries often runs double the bare-tool price.
Frequently Asked Questions
What is the top rated portable table saw?
The DEWALT DWE7491RS is our top-rated portable table saw based on eight weeks of hands-on testing. Its 32-1/2 inch rip capacity, rack and pinion telescoping fence, and rolling stand set it apart. It averages 4.7 stars across 5,789 buyer reviews, with 87 percent of owners rating it 5 out of 5.
What is the best portable table saw for the money?
The SKIL TS6307-00 offers the best value in our roundup. It pairs a 10 inch blade, 4×4 cutting capacity, and a rack and pinion fence with a folding stand at a price well below the premium competitors. For occasional DIY and weekend projects, it is hard to beat.
Which portable table saw has the best fence?
The DeWalt DWE7491RS and DWE7485 both use the same rack and pinion telescoping fence design, which we rated the best in this roundup. The SKILSAW SPT99-11 uses a similar system on its worm drive model. Bosch GTS15-10 adds color coded index pins that line up with a printed scale for fast, repeatable adjustments.
What is the lightest portable table saw with a stand?
The SKIL TS6307-00 at 51.2 pounds is the lightest 10 inch saw with an integrated stand in this roundup. The DEWALT DWE7485 at 54 pounds is the lightest with a roll cage base but no folding stand. For a true under 20 pound option, the WORX BladeRunner WX572L at 14.7 pounds handles small craft cuts only.
What size blade should I get for a portable table saw?
A 10 inch blade is the standard for full-size portable table saws and accepts the widest range of dado sets and aftermarket blades. An 8-1/4 inch blade saves weight and works fine for trim, plywood, and 2x lumber, but limits depth of cut to about 2-1/2 inches. Choose 10 inch if you cut 4×4 posts or thick hardwood regularly.
Final Verdict
After eight weeks of testing ten of the best portable table saws on the market, our top recommendation is the DEWALT DWE7491RS for its combination of rip capacity, fence accuracy, and rolling stand convenience. If you need worm drive torque for framing or treated lumber, the SKILSAW SPT99-11 is the saw to buy. For the best portable table saw under tight budgets, the SKIL TS6307-00 delivers real 10 inch performance without the premium price.
Whatever you choose, upgrade the stock blade to a quality 40 to 60 tooth ATB design, keep the blade guard and riving knife installed, and treat the fence as the precision instrument it is. A well-tuned portable table saw will out-cut a poorly set up cabinet saw every time.
For more tool roundups, check out our guides on 8 Best 12 Inch Miter Saws On The Market Reviews, 8 Best Portable Table Saws with Laser Tested, 8 Best Table Saws for Professionals Reviews, 8 Best Table Saws for Accuracy Transparent reviews, and 8 Best Miter Gauge for Table Saws Reviewed.